Hydraulic Valves

COUNTER BALANCE VALVES

Used for both single- and double-acting hydraulic cylinders, these valves provide positive holding and controlled ‘chatter-free’ lowering of loads. The valve includes 2 male and female couplers, 2 hydraulic hoses, hydraulic fittings and dust caps. (The valve can also be supplied without these additional components, as you require).

 

METERING VALVES

Power Team metering valves have an in-line automatic design for systems using large cylinders or extended lengths of hydraulic hose. They can be used with both single- and double-acting hydraulic cylinders. The metering valve provides automatic surge control when the flow exceeds 26 l/min.

 

 

PILOT OPERATED CHECK VALVE

Suited for use with open or tandem centre hydraulic valves, these robust valves optimise free single-direction flow of hydraulic fluid. The valve is designed so that fluid flow is blocked in the opposite direction until pilot oil pressure is applied. In so doing, loss of hydraulic pressure is prevented should the valve be shifted or the pump line is broken.

 

ONE-WAY CHECK VALVES

Our one-way hydraulic check valves utilise a rugged design for unidirectional flow of hydraulic fluid in your hydraulic system. The valve is fitted directly in your hydraulic line. It is designed for single-acting cylinder applications.

 

PRESSURE REDUCING VALVE

These in-line automatic valves are designed for independent pressure control to 2 or more clamping systems operated by a single hydraulic power source. The high-quality design of this pressure control valve range allows operators to control a single continuous pressure source to supply various pressures in different stages of a single system.

 

PRESSURE REGULATOR VALVES

These are a reliable, high-quality pressure safety valve solution for adjusting operating pressure at various values below a pump’s relief valve setting.

It is easily adjusted to maintain pressures between 20 and 700 bar, with a flow range of 0.31 to 23 l/min, and can be used with single- or double-acting cylinders.

 

PRESSURE RELIEF VALVE

Ideal for remote locations in a hydraulic circuit, where maximum pressure requirements are less than basic overload valve settings in a pump. The in-line hydraulic pressure relief valve is adjustable from 70 to 700 bar and can be used with both single- or double-acting cylinders.

 

RELIEF VALVES

Relief valves are a critical part in the health and safety of your hydraulic system and prevent potential machine damage, protecting the circuit from over-pressurisation. Our hydraulic overpressure valve range includes in-line automatic relief valves designed for a maximum flow rate of 19 l/min.

 

SEQUENCE VALVES

These in-line automatic valves provide precise cylinder sequencing functionality in multi-cylinder hydraulic applications. A simple operation for ease of use – the pump is connected to one port and separate cylinders to another two ports. When pressure is applied to the pump-connected port, the first cylinder port advances and the other will not advance until a pre-determined pressure level in the cylinder is reached.

 

LOAD LOWERING VALVES

Designed for precision metering for controlled cylinder piston return, these in-line manual valves permit free-flow until the operator can open a locked valve.

The load lowering valve can be pre-set for a constant measured return, or the rate of return can be operator selected with each actuation. It has an operating pressure of 700 bar and 19 l/min.

 

SHUT OFF VALVES

These in-line manual needle valves are designed to allow fine metering of hydraulic oil and for controlling multiple single-acting cylinders. These shut off valves are designed with 3/8” NPTF ports.

3-WAY 4-POSITION MANUAL PRESSURE COMPENSATED VALVES

These 3-way 4-position manual pressure compensated valves are designed for use with single-acting cylinders. The cylinder piston delivers relatively constant flow regardless of pressure between 69 and 689 bar.

 

AIR HYDRAULIC PUMP MOUNTED VALVES

Monitor pressure, loads, check valves for oil and flow metering with this air-actuated valve. Mount them directly mounted onto hydraulic pumps to provide precise performance measurement and hydraulic control. Our air-actuated valve provides up to 700 bar with maximum flow of 19 l/min. Standard 9.5 mm (3/8”) ports make these valves suited for simple mounting on a wide range of hydraulic pumps.

 

MANUAL HYDRAULIC PUMP MOUNTED VALVES

We offer a range of manual valves for direct mounting onto hydraulic pumps to monitor pressure, loads, check valves for oil and flow metering. These valves provide 700 bar performance with a maximum flow range of 19 l/min. Standard 9.5 mm (3/8”) ports means these valves are compatible with a wide range of hydraulic pumps.